Question 1

What is a carbon steel ball?

Accepted Answer

A carbon steel ball is a ball made from plain high-carbon or medium-carbon steel without the chromium alloying that defines chrome or stainless grades. Typical grades are AISI 1010, 1015, 1045, 1065, 1085, with carbon controlling core hardness and wear resistance. Carbon steel balls are the lowest-cost steel balls, used where precision, hardness, and corrosion resistance are not critical.

Question 2

What is the chemical composition of carbon steel balls?

Accepted Answer

Common carbon steel ball grades are AISI 1010 (0.08-0.13 % C), 1045 (0.43-0.50 % C), 1065 (0.60-0.70 % C), and 1085 (0.80-0.93 % C). Manganese ranges from 0.30-0.90 %, silicon 0.10-0.30 %, with phosphorus and sulphur each capped at ~0.04 %. With no meaningful chromium content, hardenability is shallow compared with 52100 chrome steel.

Question 3

How hard is a carbon steel ball?

Accepted Answer

Hardness depends on grade and heat treatment. Through-hardened 1085 / 1065 reach HRC 60-65, while 1045 typically caps at HRC 45-55, and low-carbon 1010 / 1015 stays below HRB 90 unless case-hardened. For bearing-grade precision, low-carbon balls are usually case-hardened to a hard shell (HRC 60+) backed by a tough low-carbon core.

Question 4

Are carbon steel balls rust-resistant?

Accepted Answer

No. Carbon steel balls have only trace chromium and rust rapidly in humid, salty, or wet environments. They are commonly oiled, waxed, or zinc-plated for short-term storage. If the application involves water, food contact, or marine exposure, switch to chrome steel (better), 440C stainless, or 316 stainless steel balls for predictable corrosion performance.

Question 5

Are carbon steel balls magnetic?

Accepted Answer

Yes, all carbon steel balls are ferromagnetic regardless of heat treatment or carbon content. Their magnetic response is slightly weaker than 52100 chrome steel because of lower alloy content, but they will stick firmly to a magnet. Avoid carbon steel balls in non-magnetic applications such as relays, sensors, compasses, and MRI environments.

Question 6

What standards do carbon steel balls follow?

Accepted Answer

Carbon steel balls are produced in line with ASTM A510 for wire and rods, ASTM A684 for sheet, ISO 16120 for non-alloy wire, and DIN 1651 for free-cutting steel. Dimensional tolerances typically follow AFBMA / ISO 3290 grades G200-G1000 since carbon steel is rarely used for precision bearings. We supply per the agreed standard on the order.

Question 7

What precision grades are available for carbon steel balls?

Accepted Answer

Common carbon steel ball grades are G200, G500, G1000 and G2000 (non-precision). The achievable roundness and lot diameter variation are looser than for chrome or stainless because of shallower hardening and lower-grade lapping. For precision bearings, instrument bearings, or ball screws, we recommend upgrading to 52100 chrome or 440C stainless steel.

Question 8

What size range of carbon steel balls do you supply?

Accepted Answer

Our standard carbon steel ball range spans 2 mm to 100 mm diameter, with cold-headed low-carbon balls available down to 1 mm. Larger diameters above 100 mm are produced by hot forging or machining. Carbon steel is most common in the 5-50 mm range for track ball, furniture caster, drawer slide, and toy applications.

Question 9

Where are carbon steel balls used?

Accepted Answer

Carbon steel balls appear in drawer slides, furniture casters, shopping cart wheels, sliding door rollers, toy casters, bicycle kickstand balls, agricultural bearings, automotive seat adjusters, and many low-cost industrial pivot or strike applications. They are also widely used as base balls that are subsequently case-hardened or chrome-plated.

Question 10

Carbon steel vs chrome steel ball - which should I choose?

Accepted Answer

Carbon steel balls are 30-60 % cheaper than equivalent-size chrome steel (52100) balls and 70 % cheaper than stainless steel balls. Choose carbon steel for non-precision, dry, indoor, low-load applications where surface rust is acceptable. Choose chrome steel when you need precision grades G100 or tighter, deeper hardness, or longer wear life.

Question 11

Can carbon steel balls be case hardened?

Accepted Answer

Yes. Low-carbon grades (1015, 1018, 1020) are routinely carburized or carbonitrided at 880-930 °C to produce a hard wear shell of HRC 60-62 while keeping a tough, ductile core. Effective case depth ranges 0.5-2.0 mm depending on holding time. After quenching and low-temperature temper the balls become competitive with through-hardened 52100.

Question 12

What coatings or platings work with carbon steel balls?

Accepted Answer

Carbon steel balls take well to zinc (electro or hot-dip), nickel, chrome (decorative and hard), black oxide, phosphate, PTFE, and electroless nickel plating. Zinc + chromate is the most common decorative / corrosion-resistant finish for shelf hardware. Hard chrome plating is used for hydraulic pump pistons and severe-wear slides.

Question 13

What is the density of carbon steel?

Accepted Answer

Carbon steel density averages 7.85 g/cm³ (0.284 lb/in³) across the common grades (1010-1085), only marginally higher than 52100 chrome steel. The mass difference vs each ball size is small enough that designers can use 7.85 g/cm³ as a default for ball weight, moment of inertia, and centrifugal force calculations.

Question 14

What temperature range can carbon steel balls handle?

Accepted Answer

Plain carbon steel balls are acceptable from about -40 °C to +150 °C in lubricated bearings. Above ~180 °C the tempered structure softens and bearings lose preload. For higher temperatures (oven conveyors, aerospace), we recommend stabilized 440C stainless (up to 250 °C), M50 tool steel (up to 315 °C), or Stellite cobalt-chrome (up to 600 °C).

Question 15

What is the minimum order quantity for carbon steel balls?

Accepted Answer

For stocked low-carbon ball diameters (2-25 mm) the MOQ is 200 kg. Custom sizes, special grades, or case hardening require 500 kg. Sample boxes of 100-200 pieces are available for stocked sizes with a sample fee refundable against bulk orders.

Question 16

What is the typical lead time for carbon steel ball orders?

Accepted Answer

Stocked low-carbon balls ship in 5-10 business days. Custom diameters, case-hardened surface, or plated finish take 25-35 days. Recurring production orders run 15-25 days once tooling and chemistry are locked in. We confirm dispatch dates in the order acknowledgement.

Question 17

Are certificates available for carbon steel balls?

Accepted Answer

Carbon steel ball shipments include an EN 10204 2.1 certificate of compliance. A 3.1 mill certificate covering chemistry, hardness and dimensional inspection is supplied on request, plus ISO 17025 lab reports from independent agencies (SGS / BV) when required. Plating certificates reference ASTM B633 (zinc) or ASTM B733 (electroless nickel).

Question 18

How are carbon steel balls packaged?

Accepted Answer

Carbon steel balls are packed in poly-bags with anti-rust oil inside cartons (25 kg net) or steel drums (50-200 kg). For long-term storage, vacuum foil with desiccants is recommended. Drum labels show size, grade, batch, and gross/net weight. Palletized 1-ton units fit a 20 ft container, suitable for FOB / CIF shipments.

Question 19

What drives the cost of carbon steel balls?

Accepted Answer

Cost is driven primarily by raw steel rod price (typically LME-correlated), ball diameter, lot size, surface finish (none vs zinc vs hard chrome), and any post-processing (heat treatment, plating, sorting). For high-volume runs we offer blank-stock plus hot-forging cost; for samples, hand-lapping and segregation raise unit cost significantly.

Question 20

Are carbon steel balls recyclable?

Accepted Answer

Yes. Carbon steel balls are made of clean, low-alloy ferrous scrap and are 100 % recyclable at end of life without special handling. At JIA XIN we typically recover 60-70 % of grinding swarf and ball rejects through certified scrap channels, supporting customers' Scope 3 reporting and circular-economy targets.

탄소강 볼

탄소강 볼

탄소강 볼

윤곽

ISO 9001

30+ Years

0.3–250mm

G3–G60

왜 Jiaxin 탄소강 공인가?

형질

화학

환경 적합성

기술 사양

재료 등급

정밀 등급

영률

표면 마감

동등한 이름

경도

인장

공급조건

직경 범위

밀도

자기

인증

재료 선택 가이드

국제 등급 등가물

1010

1015

1085

10

15

85

S10C

CK10

탄소강구를 사용하는 산업

리드타임 및 주문

기술 리소스

Frequently asked questions

What is a carbon steel ball?

What is the chemical composition of carbon steel balls?

How hard is a carbon steel ball?

Are carbon steel balls rust-resistant?

Are carbon steel balls magnetic?

What standards do carbon steel balls follow?

What precision grades are available for carbon steel balls?

What size range of carbon steel balls do you supply?

Where are carbon steel balls used?

Carbon steel vs chrome steel ball - which should I choose?

Can carbon steel balls be case hardened?

What coatings or platings work with carbon steel balls?

What is the density of carbon steel?

What temperature range can carbon steel balls handle?

What is the minimum order quantity for carbon steel balls?

What is the typical lead time for carbon steel ball orders?

Are certificates available for carbon steel balls?

How are carbon steel balls packaged?

What drives the cost of carbon steel balls?

Are carbon steel balls recyclable?

정밀 강철 볼을 원하시나요? 저희가 도와드리겠습니다!