Question 1

What is an AISI 316 / 316L stainless steel ball?

Accepted Answer

An AISI 316 / 316L stainless ball is an austenitic, non-magnetic stainless ball made from iron-chromium-nickel-molybdenum alloy containing 16-18 % Cr, 10-14 % Ni and 2-3 % Mo. The 'L' variant caps carbon at 0.03 % for improved weldability and resistance to intergranular corrosion after welding. 316 / 316L are the workhorse 'marine grade' stainless balls.

Question 2

What is the chemical composition of 316 / 316L?

Accepted Answer

316: ≤0.08 % C, ≤2.00 % Mn, ≤1.00 % Si, 16.0-18.0 % Cr, 10.0-14.0 % Ni, 2.0-3.0 % Mo, ≤0.045 % P, ≤0.03 % S. 316L: same except carbon ≤0.03 %. Molybdenum is the key differentiator vs 304 - it stabilizes the passive film and dramatically improves resistance to chloride pitting and crevice corrosion.

Question 3

How hard is a 316 / 316L ball?

Accepted Answer

Annealed 316 / 316L is about HRB 80 (roughly HRC equivalent ~ 25). Cold-worked balls (especially in the precision-grade supply chain) reach HRC 35-40. 316 cannot be hardened by heat treatment. For higher hardness with similar corrosion resistance, specify 17-4PH precipitation-hardened stainless or 440C martensitic stainless.

Question 4

How corrosion resistant is 316 / 316L stainless steel?

Accepted Answer

316 / 316L is the second-most corrosion-resistant standard stainless alloy (after higher-nickel grades such as 904L or 254 SMO) and is the standard choice for marine, salt-spray, chemical, pharmaceutical, and chloride-rich environments. Its PRE (pitting resistance equivalent) is ~25, vs 304's ~18. It passes ASTM B117 1000-hour salt-spray tests when properly passivated.

Question 5

Are 316 / 316L balls magnetic?

Accepted Answer

In the annealed condition 316 / 316L is essentially non-magnetic (magnetic permeability ≈1.005). Severe cold working (e.g., heading or burnishing) can induce slight magnetism; measurements on a finished lot typically read near-zero. If your application demands absolute magnetic neutrality, order 316L annealed and specify a 'NM' magnetic check.

Question 6

Which standards apply to 316 / 316L balls?

Accepted Answer

316 / 316L balls comply with ASTM A276, A479, A493, AMS-QQ-S-763, ISO 683-13, EN 10088-3 (1.4401 / 1.4404), and ASTM A967 for passivation. EN 10204 3.1 mill certificates are issued with every shipment. Pharmaceutical and food grades meet ASME BPE and 3-A sanitary standards.

Question 7

What precision grades are 316 / 316L balls available in?

Accepted Answer

316 / 316L are available in AFBMA / ISO 3290 grades G40, G60, G100, G200, G500 and G1000, with G100-G200 the most common stock. G10-G25 grades are difficult due to the austenitic structure's lower yield strength and are usually substituted with 440C or silicon nitride ceramic.

Question 8

What size range of 316 / 316L balls do you supply?

Accepted Answer

Standard stocked range: 0.5 mm to 100 mm. Forged large balls up to 250 mm are produced on request. Finer than 0.5 mm down to 0.2 mm are made from wire for spray nozzles and medical dispense valves. Custom sizes outside the standard range carry MOQ and lead time.

Question 9

Why is 316 preferred for marine applications?

Accepted Answer

316 contains 2-3 % molybdenum, which vastly improves resistance to chloride pitting and crevice corrosion - the two main failure modes in sea water. 304 (without Mo) suffers pitting at chloride levels above ~200 ppm. 316 withstands 1000+ hour ASTM B117 salt-spray and is the default alloy for marine hardware, deck fittings, sailboat rigging, and seawater pumps.

Question 10

316 vs 316L stainless ball - which should I choose?

Accepted Answer

Choose 316 for general marine, chemical and food-grade applications. Choose 316L when the balls will be welded, brazed, or exposed to temperatures above 425 °C, where 316's higher carbon can form chromium-carbide precipitation and intergranular corrosion. 316L is also preferred for ASME BPE sanitary tubing and pharmaceutical process equipment.

Question 11

What is the density of 316 / 316L?

Accepted Answer

Density of 316 / 316L is 7.98 g/cm³ (0.288 lb/in³). This is slightly higher than 304 (7.93 g/cm³) due to the molybdenum content. The mass difference matters for weight-sensitive aerospace or marine components and for centrifugal calculations on high-RPM mixer shafts.

Question 12

What temperature range can 316 / 316L balls handle?

Accepted Answer

316 / 316L stainless balls service -200 °C to +870 °C continuous (intermittent scaling above 800 °C). 316L is preferred from 425-870 °C to avoid sensitization. Above 870 °C austenitic stainless starts to scale rapidly; in such cases use Inconel 625 / 718 nickel alloys or Stellite cobalt-chrome balls.

Question 13

How should 316 / 316L stainless balls be cleaned?

Accepted Answer

Use warm water, mild non-chloride detergent, and a soft cloth or ultrasonic bath (40 kHz). Rinse with deionized water and dry with filtered air. Avoid bleach, hydrochloric acid, and steel wool, all of which attack the passive layer. For medical and food-grade applications, follow ASME BPE or 3-A sanitary cleaning protocols.

Question 14

316 vs 304 stainless ball - which is better?

Accepted Answer

316 is a clear upgrade over 304 in any chloride or salt environment (PRE 25 vs 18). For indoor, atmospheric, food, or low-corrosion applications, 304 is fully adequate and cheaper (typically 20-30 % less). The cost gap widens with high nickel surcharge; we recommend 316L only where the higher corrosion performance truly matters.

Question 15

Are 316 / 316L balls food and pharma grade?

Accepted Answer

316 / 316L are FDA, USDA, EU 1935/2004 and ASME BPE compliant for food and pharmaceutical contact. 316L is preferred for parenteral, biopharma and sterile-process piping due to low carbon and weldability. Each lot ships with FDA / RoHS / REACH statements and full mill traceability.

Question 16

What is the MOQ for 316 / 316L balls?

Accepted Answer

Stocked 316 / 316L balls (1-25 mm) ship with 100 kg MOQ. Custom sizes, VAR (vacuum-arc-remelted) premium grades, or pharmaceutical-grade lots require 300-500 kg. Sample boxes of 50-100 pieces ship from stock against freight collect.

Question 17

What is the lead time for 316 / 316L ball orders?

Accepted Answer

Stocked sizes ship in 5-10 business days. Custom diameters, special precision, or VAR grades take 25-40 days. Repeat orders run 15-25 days. Pharmaceutical audit-trail orders may need 35-50 days for documentation review.

Question 18

What certificates accompany 316 / 316L balls?

Accepted Answer

Mill certificate (EN 10204 3.1) covers chemistry and mechanical properties. Dimensional, surface roughness, passivation certificate (ASTM A967), salt-spray results (ASTM B117), and 3.2 third-party inspection (SGS / BV / TUV) are added on request. Pharmaceutical orders include full lot traceability and audit-trail documents.

Question 19

How are 316 / 316L balls packaged?

Accepted Answer

Vacuum foil with desiccants and oxygen absorber, then food-grade PE bags inside PE-lined cartons (20-25 kg) or drums (50-200 kg). Clean-room and pharma-grade lots use double-bag nitrogen-flushed packaging and tamper-evident seals. ISPM-15 pallets and stretch wrap for sea freight.

Question 20

What drives 316 / 316L ball pricing?

Accepted Answer

Price is driven by grade (316 vs 316L), diameter, lot size, precision, surface finish, certification level, and the LME nickel surcharge. 316 typically sells at a 30-50 % premium over 304 due to molybdenum and higher nickel. VAR premium grade adds 20-40 %. Pharma-grade add extra for documentation and audit trail.

Paslanmaz Çelik Bilye

Paslanmaz Çelik Bilye

AISI 316/316L Paslanmaz Çelik Bilye

ISO 9001

0,3–250 mm

G3–G60

Neden Jiaxin 440C Topları?

Özellikler

Kimya

Korozyon Direnci

Malzeme Sınıfı

Hassas Kaliteler

Young Modülü

Yüzey İşlemi

Eşdeğer İsimler

Hardness

Tensile

Tedarik Durumu

Çap Aralığı

Density

Magnetism

Certification

Malzeme Seçim Kılavuzu

Uluslararası Sınıf Eşdeğerleri

9Cr18Mo

SUS440C

440C

Z100CD17